Because it is accurate and effective, hardware manicure has grown in popularity. Even seasoned technicians, though, occasionally make mistakes that result in subpar work or even damage to the nails.
For anyone trying to get the most out of their technique, knowing these typical traps is essential. Whether you’re a do-it-yourself enthusiast or a professional, knowing what not to do can help you get the best results.
This post will discuss ten common hardware manicure errors and offer helpful advice on how to avoid them. You can guarantee a faultless and secure manicure each and every time by being aware of these mistakes.
| Mistake | How to Avoid It |
| Using the wrong speed on the drill | Adjust the speed according to the nail type and task |
| Not sanitizing tools properly | Always sterilize tools before and after each use |
| Applying too much pressure | Use a light hand to avoid damaging the nail |
| Skipping cuticle care | Gently push back and trim cuticles for a clean finish |
| Improperly holding the drill | Hold the drill at the correct angle to prevent injury |
| Overfilling the nails | File with care to avoid thinning the nail too much |
| Using dull drill bits | Replace drill bits regularly to ensure smooth operation |
| Not prepping the nails | Clean and buff nails before starting |
| Skipping aftercare | Moisturize and care for nails post-manicure |
- Error 1: Incomplete disclosure cuticles
- Mistake 2: Incorrect grip of the finger when processing with a cutter
- Error 3: Incorrectly selected cutter for opening the cuticle
- Error 4: Incorrect technique for scraping off the cuticle with a ball
- Error 5: Incorrect choice of abrasive density for a ball-shaped cutter
- Error 6: Too high or low cutter speed
- Error 7: Incorrect sequence of hardware manicure stages
- Error 8: Long work with a cutter in one place
- Error 9: Hardware manicure on injured skin or wet nails
- Error 10: Lack of disinfection of hands and nails
- Share with friends!
- Popular on the topic Hardware Manicure
- Section of the magazine
- Express your opinion or ask a question! Cancel the answer
- One comment on “10 errors with hardware manicure and how to avoid them”
- Video on the topic
- 4 main errors in hardware manicure. Why it does not work?!
- Beginner mistakes in manicure and coating | How to fix it?
- 10 TOP errors why the hardware manicure does not work
- 10 errors when removing gel varnish with a cutter | Why hot? 🔥
- 10 manicure errors for beginners
Error 1: Incomplete disclosure cuticles
Professional masters assure you that the most difficult step in hardware manicure is not the stage where you fear using a ball to remove the cuticle, which you believe to be the most unpredictable, but rather the very first step where you lift and open the cuticle.
It is nearly a given that you won’t be able to fully remove the cuticle with a ball if its angle is less than 90 degrees. As a result, instead of the anticipated two weeks, the manicure will last two to three days, after which the growth will resume.
Skin damage and potential inflammation are even more heinous consequences of this error if you still choose to massage the area with a ball.
Mistake 2: Incorrect grip of the finger when processing with a cutter
Working with the client’s cuticle requires holding the finger above the nail while working on the right side and grabbing it from below when working on the left.
To ensure precision in your movements when gripping with your left hand, support the finger with your right little finger. To gain broader access to the lateral cuticles, it is also advised to move the pad using the little finger.
It will be challenging for you to hold the cutter with a blunt end parallel to the nail plate if you have an improper grip on your finger. In certain places, getting to hard-to-reach places at the proper angle will require more effort on your part. Cuts in the nail may develop as a result.
Error 3: Incorrectly selected cutter for opening the cuticle
A novice could make a mistake like choosing the wrong cutter. This is particularly valid during the initial phase, when the cuticle is opening.
Experts in hardware manicures advise opening the cuticle with a blunt-ended corundum cone.
Erroneously, novices might select the widely used flame or bullet cutters.
They seem useful at first for working the area beneath the cuticle and getting rid of the pterygium, but this is a mistake:
- The diamond flame attachment has a sharp and thin nose that can injure the skin. You will have to work with it very carefully, and it will not provide the desired result at the first stage.
- Bullet attachment has a round shape and because of this it fits more tightly to the nail in the area of roundness. With the slightest pressure, it makes cuts in the nail.
Error 4: Incorrect technique for scraping off the cuticle with a ball
When using a ball-shaped cutter, there should be two steps involved. To start, turn the cuticle with a ball, or gently slide the attachment under it so that it rises at a ninety-degree angle. and only then begin using a ball to scrape the skin. It will peel off smoothly and easily.
You run the risk of developing hangnails and microtraumas if you skip the first stage and begin chopping off the semi-adjacent cuticle right away. Pterygium that hasn’t been fully removed and any remaining hanging skin should be added. These will cut the manicure’s lifespan in half or even three times.
Error 5: Incorrect choice of abrasive density for a ball-shaped cutter
Mistakenly, novices begin using a cutter with a red or even yellow notch, thinking that the cuticle ball should be softly abrasive. This is not the right strategy. The skin can be torn by the attachment, and the cleaning effectiveness is greatly reduced. An additional drawback is that the ball with the soft coating clogs easily, requiring replacement by the fifth nail.
For working with the cuticle skin, a diamond ball with a blue notch works best. The purpose of cutters with black and green markings is to remove gel polish and work with artificial nails.
Error 6: Too high or low cutter speed
Hardware manicure tools have a 30,000 rpm maximum speed. Experts can afford to operate at 10,000–12,000 rpm, while novices are advised to operate between 4,000 and 6,000 rpm. Otherwise, you can just erase the nail if you don’t have the right technique.
Set the speed to 5000 rpm once you’ve started working, and then adjust it based on how you or the client feel. If the cutter slips, increase the speed; if you experience any burning, reduce the speed a little.
Note that varying hardware manicure stages also call for varying speeds. In addition to considering your experience and the skin’s characteristics, pay attention to the advice of experts.
Error 7: Incorrect sequence of hardware manicure stages
This kind of irksome mistake can be encountered by novices in both professional and home manicures, leaving them to wonder why nothing seems to work. There are actually only four stages, not that many.
- Lifting and opening the cuticle with a corundum cone and a ball with high abrasiveness (blue notch)
- Cleaning the lateral sinuses and the area under the cuticle with bullet and ball attachments
- Cleaning the raised cuticle with a ball
- Grinding the cut with a polisher
It will be challenging to remove the skin with a ball without a high-quality raised cuticle and clean pterygium, and even a polisher won’t help to achieve the perfect surface of the treated area. The lifespan and quality of the manicure will be impacted if the instructions are not followed.
Error 8: Long work with a cutter in one place
After beginning a hardware manicure, you run the risk of making another easy but common error: focusing on one spot for an extended period of time. The results include cuts, hangnails, microtraumas, and a negative attitude in both you and the client.
Expert instructors advise against spending longer than a single second in one spot. The cutter ought to be moving all the time, from one place to another. Start operating at 4000-5000 rpm, which is the ideal speed range.
Are you scared to work with skin straight away? To practice, purchase an artificial finger or a special mannequin hand. Yes, these are available in upscale stores and are meant to instruct aspiring masters.
Hardware manicures are well-known for their accuracy and effectiveness, but frequent errors like misusing the wrong instruments or applying excessive pressure can harm the skin and nails. In order to keep your nails healthy and attractive, we’ll list the top 10 mistakes people make when getting hardware manicures in this post and provide helpful advice on how to avoid them.
Error 9: Hardware manicure on injured skin or wet nails
- Inflamed hangnails and skin around the nail – the first reason, for which it will be very problematic to make an ideal manicure. It is better to first put your nails in order, cure the inflammation, and then bring beauty.
- The second reason is wet nails. A nail plate saturated with moisture is extremely difficult to process. You can damage not only the skin of the cuticle and the nail, but also the device itself. The attachments can become clogged with wet particles and you will have to stop the process to bring the cutters into working condition.
You’ll need a way to degrease or dry your nails in this case. In a matter of seconds, it will complete the task, allowing you to get to work.
Error 10: Lack of disinfection of hands and nails
The first step in hardware manicure protocol is to thoroughly clean the cutter attachments. However, a lot of novices overlook the importance of hand hygiene. Microtraumas are highly likely to occur during the procedure. Inflammation may occur if bacteria or an infection enters the wound.
Purchase Sterillium, Octenisept, or Chlorhexidine, and apply them to your hands prior to performing the procedure to prevent such unpleasant outcomes. More information regarding antiseptics and hand hygiene for the client and the master.
Share with friends!
Popular on the topic Hardware Manicure
Materials, detailed instructions, and design concepts for nail painting
The top 7 manicure and pedicure device models: pick and assess
Ideas for orange manicures
For nail art, use sprinkles and loose decorations.
What kind of manicure is in right now? 2024’s hottest nail designs
Ideas for pastel manicure designs
Valentine’s Day manicure: gel polish design painting
Rhinestone manicure: varieties, concepts, guidelines for creating and adhering crystals to nails
Velvet heart: Nail art with flocus or floking of the nails
Extend a lance gel for an express manicure
Section of the magazine
Express your opinion or ask a question! Cancel the answer
One comment on “10 errors with hardware manicure and how to avoid them”
Inna
It was only because of these suggestions that the cut came out smoothly. I don’t know, nothing happened at all, and I already wanted to quit doing manicures. I’m grateful.
Making no mistakes when it comes to hardware manicure is essential for both pros and do-it-yourselfers. You can greatly enhance your technique and the general health of your nails by being aware of common mistakes like using the incorrect bit, applying too much pressure, or omitting important steps like sanitizing.
Recall that practice makes perfect. With increased familiarity with the tools and techniques, avoiding these mistakes will get easier. By taking the time to understand and use the proper techniques, you can guarantee that your manicures are both gorgeous and secure.
Ultimately, perseverance and meticulousness are essential for a hardware manicure to be successful. You can benefit from professional-looking nails without running the risk of damage by being informed and cautious.
